Updates to my bicycle wheel spinning wheel

A long while back, I built a spinning wheel out of a bunch of junk in the garage.



You might like reading the posts where I discuss the progression of this design -


While it worked very nicely, and while I really enjoyed using it, setting it up and taking it down was a royal pain in the neck because it was all clamped together.  Sooooo..... I decided to work on the frame and make it more user friendly.

Meet my new wheel!  (All photos click for enlargement)


The base is the same,, but I'm using a different wheel - my garage is overflowing with spare wheels - and pretty much everything else has been replaced.  But - LOOK!  It folds up!


Everything can now slip into an 8 inch wide slot between boxes in my fiber storage area.  Ten big shouts of joy over that one!  Yay!

So, let me give you a tour of my new wheel.

First, let's look at some measurements.  The wheel itself measures approximately 25.5 inches across.


Cleaning it of road gook is possibly the most difficult and distasteful part of the entire project.  I hated that part - it took forever and I hated every minute of it.  I cleaned all of the spokes, and I cleaned the rim inside and out (I didn't clean the hub), and how I hated that job.  In fact, I forgot how I cleaned it - I used some sort of solvent and a lot of paper towels and I blocked it all from my mind.

I kept the same base as in the original version of the wheel, and the center part measures 


about 31 inches long, and the wheel side of the base measures about 15.5 inches long, while the


spindle side measures just a little less.  Why?  Because I needed to make room for the wing nut.  Oops.  Poor planning.  *blush*  It still works just fine, and a little asymmetry is aesthetically pleasing, isn't it?


The base is made from previously used (and exceedingly bunged up) pine 2 by 4's.

The spindle arm measures about 16.25 inches long, 


and is about 3.5 inches wide.


The wheel arm measures about 26.5 inches long.


Both of these are made of maple - the wheel arm is wider at the base 


than at the wheel end 


- it came that way from the lumber yard and this is why it is sitting, unused, in my garage.  Like I said, my wheel is a little asymmetric, and this is perfectly OK with me.

So that my wheel can be folded and moved about, I felt it necessary to peg the arms in place so that they don't flop around while in transit.

Here you can see the peg for the spindle arm - one of an old pair of knitting needles which I made for some project a while back.  They are made out of oak, which makes for a poor knitting needle, but which makes for an excellent peg.  






I put the peg back into the base so that I don't lose it.  I lose lots of things, and I have cats who help me lose things, which only makes matters worse.  You'll see that it is in numerous spots on my table throughout this photo shoot, but in reality, I store the pegs in their holes when I'm spinning.  Really, I do, lol.




(If you click the photo, above, to enlarge it, you'll see that I've countersunk the original bolts - same on the other side of the base.  The spindle arm couldn't rotate with the bolts sticking out.)

The arm rotates up and then I tighten the eye bolt and wing nut to hold it into place.  I picked eyebolts and wing nuts for this project because I didn't want to have to depend on tools.  That was before I discovered that I'm made out of some wimpy stuff because they still hurt my fingers.... sooo..... I made this little wrench out of some left over maple - it works great!


I operate the wing nut with the maple wrench, and I stick the peg through the eye bolt so that it can lever against the table top, and it prevents the eyebolt from just turning around and around.


 It works fantastically, and no hurt fingers!  yay!

The maple is left over from this awesome counter top, made by handsome husband,


It's just gorgeous, and I've found a hundred uses for the little left over pieces.

Here are more views of the pegs and the wrench,




and the wrench stores in the wheel arm peg,


After these photos were made, I added two little brass screws, one on either end of the wrench, just because I never really trust gluing these things together, plus the little brass screws look nice.  I'll have to show you sometime.



The spindle arm has a rounded base so that it can easily swing into position, and also so that it can be tilted one way or the other as needed.   It works great.  The wing nut doesn't need to be tightened ferociously tight, it just needs to be tight enough so that the arm stands up.  Once you get it set, it stays there during use, even though you would be able to move it with light force.

Moving right along.... the spindle holder - 


I swing it up and tighten it into place.  I'm using the same spindle holder, or "spindle head" (is this even a correct term?) that I've been using for quite a while now.  It works great.  I've made a small change to the point where the band hits the spindle, but I'll get to that later.

Next, it's time to raise the wheel arm.  It folds down onto the base and rests on two little dowels, and it gets held in place by the peg that you saw earlier.



You can barely see the pegs in the center and to the right, under the wheel arm.  You can see the holding peg on the left.

I start by raising it so that it stands vertically, and I gently tighten the nut.




It doesn't need to be really tight, it just needs to hold still for a little while.

On the arm, you can see two copper straps.  


Years ago, I cut pieces from a copper pipe, flattened them with a hammer and anvil, drilled two holes in them and then bent them in such a way so that they held a basket onto my baby stroller.  The baby in question is now almost 21, so you can see that I never throw anything away, heh.  I am thrilled to be able to use them for this project.  

I flattened them out again, 


and mounted them on the wheel arm.  I mounted them at a slant because they wouldn't fit crossways.  There are wingnuts on the other side.


The bicycle wheel is mounted onto a file,



because I had a file and it was handy.  You might be able to find something else lying around which would work even better.

Looking down the wheel arm, you can see where the file will fit.


It seems like it ought to be difficult to lift the wheel onto the arm, but surprisingly, it's not - I was able to do it onehanded, and still take photos of the operation, which sort of surprised me.



The wingnuts need to be only barely tightened - they really aren't holding anything in place, gravity holds everything together nicely.


Be sure that the wheel is sitting on the arm like in the photo above, and not like in the photo below.


Next, I lower the arm out to the right in the proper position, and I'm ready to spin!






This is enough for one night - next time we meet, I'lll show you how to set up for spinning.  In the meanwhile, here's a photo to prove that it actually does work!


Stay tuned!

Encourage one another...

My Baby Girl Won a Photography Contest!

.
My youngest, Emma, age 14, entered the local newspaper's Summer Fun photo contest and she won first prize in the high school division! She won a nice little camera! WOOT!

Here is her winning photo,



 which is a self portrait, taken with a tripod, timer, ladder and 9,000,000 takes.  The author of the newspaper article which summed up the contest called it "Highly creative."  I have to agree.  I also have to wonder if he had any idea how much work went into it.

She entered 10 photos, and here are the others - 


legs


legs


a friend's legs


OK, I guess this one is more "feet" than "legs" but I'm spotting a distinct pattern here.


I have to admit that I didn't understand this one (above) until she pointed out the colorful footprints.  Another self portrait which featured a timer, a tripod and this time, a box. 


This is the upper part of the girl in the argyle socks, above, heh.


And, here's just about all of her!  I love love love these two photos, the ones above and below this comment.  I love how two clubs are in the air in the photo above, and I love the expression on the girl's face in the one below.  There are about 75 other photos from this session, and they are all fantastic.  I don't know  how Emma narrowed it down to only two entries.


A hollyhock.  She took this photo much earlier in the summer, and this morning, months later, I saw the exact same image out in the yard - the sun shining through a watermelon-colored hollyhock.  I took it as a sign to blog about the photo contest!


If you'd like to see more of my darling's photos, then please visit her blog, Cinnamon Thicket.

Emma and Teelin, the juggling girl in the photos, have a juggling video online, maybe you'd like to see it?  The camera was set all wonky, so the image quality isn't too good, but still, I think it's cute.  Watch the little brown dog, heh.

Encourage one another


.